Author: adminizon

RadiantPERT ™ HEATING, COOLING, and SNOW MELTING LIMITED WARRANTY From Watts Radiant™
1. Watts Radiant warrants its RadiantPERT tubing, fittings, and factory manufactured manifolds to be free of defects in material and workmanship when used under normal conditions in hydronic heating, cooling, and snow melting systems. Tubing is warranted for a period of twenty-five years from the date of manufacture. Watts Radiant manufactured manifolds and fittings are warranted for a period of two years from the date of manufacture. All other RadiantPERT accessories are warranted for a period of one year from the date of installation.
2. In the event of any such defects during the warranty period, Watts Radiant’s obligation will be to repair or replace, at its discretion, any material that is covered under this warranty and proven to be defective. In the event of a system malfunction or leak caused by defective materials (and not by incorrect installation procedures, handling procedures or jobsite conditions) a reasonable, preapproved amount will be allowed for repair materials and repair labor. In the event of a leak occurring in a factory manifold, you may contact Watts Radiant for a free replacement manifold or any needed parts (freight prepaid). In the case of field-assembled manifolds, Watts Radiant warrants the quality and serviceability of the individual components sold by Watts Radiant that the contractor incorporates in that manifold, but Watts Radiant cannot warrant the complete manifold assembly or any field-assembled connections. That is the responsibility of the installing contractor.
3. In order to qualify for a warranty remedy under paragraph 2 above, you must contact Watts Radiant in advance and receive a written authorization for this allowance. Repair materials, repair labor and freight expenses not authorized in writing in advance by Watts Radiant in this way will not be compensated.
4. To qualify for the above warranty you must do the following:
a. Use good construction techniques to install our materials, as specified in our current design and installation guidelines and technical notes. This must include field pressure testing our materials before they are covered by concrete or otherwise made inaccessible.
b. Install our materials according to all specific instructions furnished for your installation.
c. Install RadiantPERT in a system that will not operate at temperatures exceeding ratings as marked on the tubing.
d. Product must be installed in compliance with all applicable plumbing, heating, cooling, and/or mechanical codes.
5. Evidence of tampering, mishandling, neglect, accidental damage, freeze damage, or unauthorized repairs that cause damage to Watts Radiant products will void any warranty coverage. All design and tubing-to manifold connections are specifically excluded from the terms of this warranty.
6. Watts Radiant provides a complete radiant system offering so that it is possible to complete an installation with Watts Radiant products. However, it is possible that other manufacturers’ tubing and/or fittings may be installed in any given installation. Provided that the tubing and/or fittings are manufactured to the applicable ASTM standards, and have been certified by a recognized thirdparty testing agency, the Watts Radiant product in the given installation will continue to be covered under this warranty. In the event of a system malfunction or leak that has other tubing and/or fitting manufacturers’ components installed within the failed system, Watts Radiant will be responsible only for Watts Radiant products. Products manufactured by another company should be reported to that manufacturer for their warranty response.
7. THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY GIVEN BY WATTS RADIANT WITH RESPECT TO THE PRODUCTS IN PARAGRAPH 1. WATTS RADIANT MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. WATTS RADIANT HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
8. The remedy described above shall constitute the sole and exclusive remedy for breach of warranty, and, apart from that remedy, Watts Radiant shall not be responsible under any legal theory for any incidental, special or consequential damages, including without limitation, lost profits or the cost of repairing or replacing other property which is damaged if the products do not work properly, other costs resulting from labor charges, delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, adverse chemical environments, or any other circumstances over which Watts Radiant has no control. This Limited Warranty shall be invalidated by any abuse, misuse, misapplication or improper installation of the products.
Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages. Therefore the above limitations may not apply to you. This Limited Warranty gives you specific legal rights, and you may have other rights that vary from state to state. You should consult applicable state laws to determine your rights. SO FAR AS IS CONSISTENT WITH APPLICABLE STATE LAW, ANY IMPLIED WARRANTIES THAT MAY NOT BE DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL SHIPMENT.

---

RadiantPEX+™ and RadiantPEX® HEATING, COOLING, and SNOW MELTING LIMITED WARRANTY From Watts Radiant™
1. Watts Radiant warrants its RadiantPEX+ & RadiantPEX cross-linked polyethylene tubing, fittings, and factory manufactured manifolds to be free of defects in material and workmanship when used in hydronic heating, cooling, and snow melting systems. This limited warranty for tubing is valid for a period of twenty-five years from the date of manufacture. This limited warranty for Watts Radiant manufactured manifolds and fittings expires two years from the date of manufacture. All other RadiantPEX+ & RadiantPEX accessories are warranted for one year after date of installation.
2. Watts Radiant’s obligation will be to repair or replace, at its discretion, any material proven to be defective when such material is covered under the following limited warranty.
3. In order to qualify for a labor allowance to repair or replace defective materials, you must contact Watts Radiant in advance and receive a written authorization for this allowance. Labor and freight expenses not authorized in writing in advance by Watts Radiant will not be compensated.
4. In the event of a system malfunction or leak caused by defective materials (and not by incorrect installation procedures or damage from handling procedures/jobsite conditions) repair materials and a reasonable labor allowance will be allowed. In the event of a leak occurring in a factory manifold, you may contact Watts Radiant for a free replacement manifold or any needed parts (freight prepaid). In the case of field-assembled manifolds, Watts Radiant warrants the quality and serviceability of the individual components sold by Watts Radiant that the contractor incorporates in that manifold, but Watts Radiant cannot warrant the complete manifold assembly or any field-assembled connections. That is the responsibility of the installing contractor.
5. To qualify for the above warranty you must do the following:
a. Use good construction techniques to install our materials, as specified in our current design and installation guidelines and technical notes. This must include field pressure testing our materials before they are covered by concrete or otherwise made inaccessible.
b. Install our materials according to all specific instructions furnished for your installation.
c. Install RadiantPEX+ or RadiantPEX in a system that will not operate at temperatures exceeding ratings as marked on the tubing.
d. Product must be installed in compliance with all applicable plumbing, heating, cooling, and/or mechanical codes.
6. Evidence of tampering, mishandling, neglect, accidental damage, freeze damage, or unauthorized repairs that cause damage to Watts Radiant products will void any warranty coverage for these particular damages, although it will not void warranty coverage for unrelated items. Field repair joints and tubing-to-manifold connections are specifically excluded from the terms of this warranty.
7. Watts Radiant provides a complete radiant system offering so that it is possible to complete an installation with Watts Radiant products. However, it is possible that other manufacturers’ tubing and/or fittings may be installed in any given installation. Providing that the tubing and/or fittings are manufactured to the applicable ASTM standards, and have been certified by a recognized third-party testing agency, the Watts Radiant product in the given installation will continue to be covered under this warranty. In the event of a system malfunction or leak that has other tubing and/or fitting manufacturers’ components installed within the failed system, Watts Radiant will be responsible only for Watts Radiant products. Products manufactured by another company should be reported to that manufacturer for their warranty response.
WATTS RADIANT DISCLAIMS ANY WARRANTY NOT PROVIDED HEREIN, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. WATTS RADIANT FURTHER DISCLAIMS ANY RESPONSIBILITY FOR SPECIAL, INDIRECT, SECONDARY, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT, INCLUDING INCONVENIENCE OR LOSS OF USE OR THE COST OF REPLACING OR REPAIRING OTHER PROPERTY WHICH IS DAMAGED IF THIS PRODUCT DOES NOT WORK PROPERLY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE FACE OF THIS DOCUMENT. NO AGENT OR REPRESENTATIVE OF WATTS RADIANT HAS ANY AUTHORITY TO EXTEND OR MODIFY THIS WARRANTY UNLESS SUCH EXTENSION OR MODIFICATION IS MADE IN WRITING BY A CORPORATE OFFICER.
8. Some states do not allow the exclusion or limitation of incidental or consequential damages and some states do not allow limitations on how long implied warranties may last. Therefore, the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

---

RadiantPEX-AL
HEATING and SNOWMELTING WARRANTY
From Watts Radiant™
1. Watts Radiant warrants its RadiantPEX-AL cross-linked polyethylene/aluminum/cross linked polyethylene tubing, fittings, and factory manufactured manifolds to be free of defects in material and workmanship when used in hydronic heating and snowmelting systems. This warranty for tubing is valid for a period of twenty-five years from the date of manufacture, unless Watts Radiant issues a special written warranty specifying a different period of time. This warranty for Watts Radiant manufactured manifolds and fittings expires two years from the date of manufacture. All other RadiantPEX-AL accessories are warranted for one year after date of installation.
2. Watts Radiant’s obligation will be to repair or replace, at its discretion, any material proven to be defective when such
material is covered under the following limited warranty.
3. In order to qualify for a labor allowance to repair or replace defective materials, you must contact Watts Radiant
in advance and receive a written authorization for this allowance. Labor and freight expenses not authorized in
writing in advance by Watts Radiant will not be compensated.
4. In the event of a system malfunction or leak caused by defective materials (and not by incorrect installation procedures
or damage from handling procedures/jobsite conditions) repair materials and a reasonable labor allowance will be allowed. In the event of a leak occurring in a factory manifold, you may contact Watts Radiant for a free replacement manifold or any needed parts (freight prepaid). In the case of field-assembled manifolds, Watts Radiant warrants the quality and
serviceability of the individual components sold by Watts Radiant that the contractor incorporates in that manifold,
but Watts Radiant cannot warrant the complete manifold assembly or any field-assembled connections. That is the
responsibility of the installing contractor.
5. To qualify for the above warranty you must do the following:
a. Use good construction techniques to install our materials, as specified in our current design and installation guidelines and technical notes. This must include field pressure testing our materials before they are covered by concrete or otherwise made inaccessible.
b. Install our materials according to all specific instructions furnished for your installation.
c. Install RadiantPEX-AL in a system that will not operate at temperatures exceeding 200°F at 80 PSIG, or as marked on the tubing.
d. Product must be installed in compliance with all applicable plumbing, heating, and/or mechanical codes.
6. Evidence of tampering, mishandling, neglect, accidental damage, freeze damage, or unauthorized repairs that cause damage to Watts Radiant products will void any warranty coverage for these particular damages, although it will not void warranty coverage for unrelated items. Field repair joints and tubing-to-manifold connections are specifically excluded from the
terms of this warranty.
7. Watts Radiant provides a complete radiant system offering so that it is possible to complete an installation with Watts Radiant products. However, it is possible that other manufacturers’ tubing and/or fittings may be installed in any given installation. Providing that the tubing and/or fittings are manufactured to the applicable ASTM standards, and have been
certified by a recognized third-party testing agency, the Watts Radiant product in the given installation will continue to be covered under this warranty. In the event of a system malfunction or leak that has other tubing and/or fitting manufacturers’ components installed within the failed system, Watts Radiant will be responsible only for Watts Radiant products. Products manufactured by another company should be reported to that manufacturer for their warranty response.
WATTS RADIANT DISCLAIMS ANY WARRANTY NOT PROVIDED HEREIN, INCLUDING ANY IMPLIED WARRANTY OF THE MERCHANTABLE OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. WATTS RADIANT FURTHER DISCLAIMS ANY RESPONSIBILITY FOR SPECIAL, INDIRECT, SECONDARY, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT, INCLUDING INCONVENIENCE OR LOSS OF USE. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE FACE OF THIS DOCUMENT. NO AGENT OR REPRESENTATIVE OF WATTS RADIANT HAS ANY AUTHORITY TO EXTEND OR MODIFY THIS WARRANTY UNLESS SUCH EXTENSION OR MODIFICATION IS MADE IN WRITING BY A CORPORATE OFFICER.
8. Some states do not allow the exclusion or limitation of incidental or consequential damages and some states do not allow limitations on how long implied warranties may last. Therefore, the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

---

Electric Floor-warming Products 25-year Limited Warranty
Watts Radiant (the Company) warrants its electric floor heating mats and cables (the Products) to be free from defects in materials and workmanship for twenty-five (25) years from the date of
manufacture. Thermostats and controls sold by Watts Radiant are warranted, parts and materials, for two (2) years from the date of purchase. The sole remedy for controls is product replacement. This warranty is only provided to customers who purchase the Products from authorized resellers, and is transferable to subsequent owners of properties where the Products are initially installed.

Under this Limited Warranty, the Company will provide the following:
If the Product is determined by the Company to be defective in materials and workmanship, and has not been damaged as a result of abuse, misapplication or modification, the Company will refund all or part of the manufacturer’s published list price of the Product at the time of purchase in accordance with the following: 100% for the first ten (10) years, then prorated on a diminishing 25-year scale for the remaining warranty period.
For example:
(1) Product found defective in the 5th year will receive the full manufacturer’s published list price of the Product at the time of purchase;
(2) Product found defective in the 15th year, with 10 years remaining in the warranty period, will receive 10/25ths of the manufacturer’s published list price of the Product at the time of purchase.

In order to make a claim, you must:
(a) Provide the Company with sufficient details relating to the nature of the defect, the installation, the history of operation, and any repairs that may have been made.
(b) At the Company’s discretion and at the owner’s expense, ship the Product to the Company or the Company’s local representative or distributor.
(c) Provide proof that the Product was installed in accordance with the applicable Product Installation Manual and any special written design or installation guidelines by the Company for this project.
(d) Provide proof that the Product was installed in accordance with the National Electrical Code (NEC) or the Canadian Electrical Code (CEC), and all applicable local building and electrical codes.
(e) Provide a retail sales receipt or proof of purchase. The following are not covered by this Limited Warranty:
(a) Any incidental or consequential damage, including inconvenience, loss of time or loss of income.
(b) Any labor or materials required to repair or replace the Product or control, not authorized in writing by the Company.
(c) Any labor or materials required to remove, repair or replace flooring materials.
(d) Any freight or delivery costs related to the Product, the control, or any related flooring or electrical products.

The Company assumes no responsibility under this warranty for any damage to the Product caused by any trades people, visitors on the job site, or damage caused as a result of post-installation
work. The staff at the Company is available to answer any questions regarding the proper installation or application of the Product at this toll-free phone number: (800) 276-2419. If you are ever in doubt about the correct installation procedure to follow, or if the Product appears to be damaged, you must call us before proceeding with the installation, or proposed repair.

THE COMPANY DISCLAIMS ANY WARRANTY NOT PROVIDED HEREIN, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. THE COMPANY FURTHER DISCLAIMS ANY RESPONSIBILITY FOR SPECIAL, INDIRECT, SECONDARY, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT, INCLUDING INCONVENIENCE OR LOSS OF USE. THERE ARE NO
WARRANTIES WHICH EXTEND BEYOND THE FACE OF THIS DOCUMENT. NO AGENT OR REPRESENTATIVE OF THE COMPANY HAS ANY AUTHORITY TO EXTEND OR MODIFY THIS WARRANTY UNLESS SUCH EXTENSION OR MODIFICATION IS MADE IN WRITING BY A CORPORATE OFFICER. DUE TO DIFFERENCES IN BUILDING AND FLOOR INSULATION, CLIMATE, AND FLOOR COVERINGS, THE COMPANY MAKES NO REPRESENTATION THAT THE FLOOR TEMPERATURE WILL ACHIEVE ANY PARTICULAR TEMPERATURE, OR TEMPERATURE RISE. UL® STANDARD LISTING REQUIREMENTS LIMIT THE HEAT OUTPUT OF REGULAR MATS AND CABLES TO 15 WATTS PER SQUARE FOOT DEPENDING ON CABLE INSTALL SPACING, AND UNDERFLOOR MATS TO 10 WATTS PER SQUARE FOOT, AND AS SUCH, USERS MAY OR MAY NOT BE SATISFIED WITH THE FLOOR WARMTH THAT IS PRODUCED. THE COMPANY DOES WARRANT THAT ALL PRODUCTS WILL PRODUCE THE RATED OUTPUT LISTED ON THE PRODUCT NAMEPLATE, WHEN OPERATED AT THE RATED VOLTAGE.

Some states do not allow the exclusion or limitation of incidental or consequential damages and some states do not allow limitations on how long implied warranties may last. Therefore, the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. SO FAR AS IS CONSISTENT
WITH APPLICABLE STATE LAW, ANY IMPLIED WARRANTIES THAT MAY NOT BE DISCLAIMED, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO TWENTY-FIVE YEARS FROM THE DATE OF MANUFACTURE.

Warranty Info Taken From:

wattsradiant.com

1. All products sold by Warmzone are warranted by the product Manufacturer. Warmzone offers no warranty of any kind, expressed or implied, with respect to the Product sold hereunder. Any and all warranty claims should be directed to the Manufacturer.
2. No representative of Warmzone is authorized to make any warranties, promises, or representations as to any Product, and none shall be binding upon Warmzone.
3. Warmzone shall not be liable for any delay in or impairment of performance resulting in whole or in part from acts of God, labor disruptions, shortages, inability to produce Product, supplies or raw materials, severe weather conditions, or any other circumstances or causes beyond the control of Warmzone.
4. Copies of Product Warranty shall be transmitted by Buyer to all subsequent purchasers. Buyer shall give Manufacturer prompt oral and confirmed written notice of Product that Buyer considers to be subject to Warranty claim.
5. Since the use of these products is beyond our control there is no express or implied warranty of results or of fitness for use. The product is furnished upon the condition that the user will determine the suitability and fitness of use of the product for any use to which it is put as well as for its inclusion as a component in any other product; that he/she assumes all risks whatsoever, that the manufacturer and Warmzone shall not be liable for any injury, loss or damage, direct or consequential, arising as a result of the use of or inability to use the product or its use in connection with or as part of any other product.

Warranty Info Taken From:

warmzone.com

WarmlyYours Snow Melting and Slab Heating Warranty

WarmlyYours, Inc. warrants the WarmlyYours snow melting and slab heating cables and mats (“the Product”) to be free from defects in materials and workmanship for ten years from the date of purchase, provided that the Product is installed in accordance with the WarmlyYours product installation guide, any special written or oral design or installation guidelines provided by WarmlyYours for the specifi c project that the Product is intended, the provisions of the National Electric Code (NEC), and all applicable local building and electrical codes. If the Product is determined to be defective in materials and workmanship, and has not been damaged as a result of misuse, misapplication or improper installation, WarmlyYours will replace the Product or refund the original cost of the Product. Controls sold under the WarmlyYours name are warranted for two years from date of purchase. Should the control be defective or malfunction, return the control to WarmlyYours and it will be repaired or replaced (at WarmlyYours’ option). The warranty does not cover removal or reinstallation costs. See entire warranty in packaging. Other controls carry their manufacturer’s warranty. WarmlyYours Inc. assumes no responsibility under this warranty for any damage to the Product prior to or during installation by anyone, including, but not limited to trades people or visitors to the job site, or damage caused as a result of post installation work. Call our toll free number, (800) 875-5285, if you have any questions about installation. The Limited Warranty is null and void if the Product owner or his representative attempts to repair the Product without receiving authorization. Upon notifi cation of an actual or possible problem, WarmlyYours will issue an Authorization to Proceed under the terms of the Limited Warranty. WarmlyYours reseves the right to void said warranty, if the product owner repairs any heating wire, for any reason.
Warranty Subject to the Following Conditions:
1. The warranty of the snow melting or slab heating system must be registered by completing and returning the attached ‘WarmlyYours Warranty Registration’ card to WarmlyYours, Inc. within thirty days of date of purchase. Please keep your invoice, as proof of date of purchase will be required in the event of a claim.
2. The snow melting or slab heating cables or mats must be installed properly under concrete, asphalt or in mortar under pavers.
3. The snow melting or slab heating system must be electrically grounded and protected by a GFI (Ground Fault Interrupter).
4. The installation must comply with all national and local electrical and building codes, as well as any other applicable statutory requirements. 5. The manufacturer hereby reserves the right to inspect the installation site at any reasonable time.
6. The warranty is not automatically transferred with change of ownership, but the manufacturer may, on application, transfer the warranty for the period remaining. This transfer is solely at the discretion of the manufacturer.
7. The snow melting or slab heating system should be used strictly in accordance with the following:
7a. Hard wire the snow melting or slab heating cables and mats to a dedicated circuit. The voltage of the circuit should match the voltage of the snow melting or slab heating system, and the size of the circuit should be such that the system does not occupy more than 80% of the circuit capacity.
7b. Should you feel no warmth from the surface that the system is installed within 60 minutes, verify that there is power to the control or thermostat. Contact WarmlyYours after verifying that there is power to the system. Under no circumstances should you or anyone else tamper with or attempt to repair the snow melt or slab heating system – this will render the warranty null and void.
7c. Switch the system on and off as you would any conventional electric heater, although timers or thermostats may be used if preferred.
7d. Use reasonable care in the operation of the system. Do not drop heavy articles, pierce or cut the surface that the heating system is installed.
7e. All restrictions and warnings detailed in the installation guide must be strictly followed.

WARMLYYOURS, INC. DISCLAIMS ANY WARRANTY NOT PROVIDED HEREIN, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. WARMLYYOURS FURTHER
DISCLAIMS ANY RESPONSIBILITY FOR SPECIAL, INDIRECT, SECONDARY, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT, INCLUDING INCONVENIENCE OR LOSS OF USE. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE FACE OF THIS DOCUMENT. NO AGENT OR REPRESENTATIVE OF WARMLYYOURS HAS ANY AUTHORITY TO EXTEND OR MODIFY THIS WARRANTY UNLESS SUCH EXTENSION OR MODIFICATION IS MADE IN WRITING BY A CORPORATE OFFICER.

Warranty Info Taken From:

warmlyyours.com

---

TempZone™ System Warranty Registration
Thank you for purchasing your new WarmlyYours TempZone™ floor warming system. To register your system, go online to www.WarmlyYours.com/warranty, or simply complete, detach and mail the Warranty Card within 30 days of date of purchase to: WarmlyYours, 590 Telser Rd Ste B Lake Zurich, IL 60047. For your convenience, you may also Fax this card to (800) 408-1100.
WarmlyYours, Inc. warrants the WarmlyYours TempZone™ electric floor warming system rolls (“the Product”) to be free from defects in materials and workmanship for twenty five (25)
years from the date of sale, provided that the Product is installed in accordance with the WarmlyYours product installation guide, any special written or oral design or installation
guidelines provided by WarmlyYours for the specific project that the Product is intended, the provisions of the National Electric Code (NEC), and all applicable local building and electrical
codes. If the Product is determined to be defective in materials and workmanship, and has not been damaged as a result of misuse, misapplication or improper installation, WarmlyYours
will, at the customer’s discretion, either refund the original cost of the Product or reimburse the cost for any labor and materials required to perform the repair or replacement of the
Product. Controls sold under the WarmlyYours name are warranted for specific coverage periods. Please see www.WarmlyYours.com for the length of warranty coverage for each
control. Should the control be defective or malfunction, return the control to WarmlyYours and it will be repaired or replaced (at WarmlyYours option). The warranty does not cover
removal or reinstallation costs. See entire warranty in packaging.

WarmlyYours Inc. assumes no responsibility under this warranty for any damage to the Product prior to or during installation by anyone, including, but not limited to trades people or
visitors to the job site, or damage caused as a result of post installation work. Call our toll free number, (800) 875-5285, if you have any questions about installation. The Limited Warranty
is null and void if the Product owner or his representative attempts to repair the Product without receiving authorization. Upon notification of an actual or possible problem, WarmlyYours
will issue an Authorization to Proceed under the terms of the Limited Warranty.

Warranty Subject to the Following Conditions: 1. The warranty of the warming system must be registered by completing and returning the attached ‘System Warranty Registration’ card
to WarmlyYours, Inc. within thirty days of date of purchase. Please keep your invoice, as proof of date of purchase will be required in the event of a claim. 2. The warming roll must be
installed flat under tile, stone, resilient flooring or laminate wood in a latex modified thinset or a portland-based cement. 3. The warming system must be electrically grounded and
protected by a GFI (Ground Fault Interrupter). 4. The installation must comply with all national and local electrical and building codes, as well as any other applicable statutory
requirements. 5. The manufacturer hereby reserves the right to inspect the installation site at any reasonable time. 6. The warranty is not automatically transferred with change of
ownership, but the manufacturer may, on application, transfer the warranty for the period remaining. This transfer is solely at the discretion of the manufacturer. 7. The warming system
should be used strictly in accordance with the following: 7.1 The voltage of the circuit should match the voltage of the warming system, and the size of the circuit should be such that the
warming system does not occupy more than 80% of the circuit capacity. 7.2 Should you feel no warmth on the floor within 60 minutes, verify that there is power to the control or
thermostat. Contact WarmlyYours after verifying that there is power through the load wires. Under no circumstances should you or anyone else tamper with or attempt to repair the
warming system – this will render the warranty null and void. 7.3 Switch the warming system on and off as you would any conventional electric heater, although timers or thermostats
may be used if preferred. 7.4 Use reasonable care in the operation of the warming system. Do not drop heavy articles on the flooring or pierce the flooring with sharp objects. 7.5 All
restrictions and warnings detailed in the installation guide must be strictly followed.

WARMLYYOURS, INC. DISCLAIMS ANY WARRANTY NOT PROVIDED HEREIN, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. WARMLYYOURS FURTHER DISCLAIMS ANY RESPONSIBILITY FOR SPECIAL, INDIRECT, SECONDARY, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT, INCLUDING INCONVENIENCE OR LOSS OF USE. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE FACE OF THIS DOCUMENT. NO AGENT OR REPRESENTATIVE OF WARMLYYOURS HAS ANY AUTHORITY TO EXTEND OR MODIFY THIS WARRANTY UNLESS SUCH EXTENSION OR MODIFICATION IS MADE IN WRITING BY A CORPORATE OFFICER.

WarmlyYours makes no claim as to the amount of floor/room temperature rise, the time to reach a given floor/room temperature or final floor/room temperature due to the innumerable variations in building construction and environmental conditions.

Warranty Info Taken From:

warmlyyours.com

---

WarmlyYours Environ II™ System Warranty
Thank you for purchasing your new WarmlyYours Environ IIJfloor warming system. To register your system, go online to www.WarmlyYours.com/warranty, or simply complete, detach and mail this postage paid Warranty Card within 30 days of date of purchase. For your convenience, you may also Fax this card to (800) 408-1100.

WarmlyYours, Inc. warrants the WarmlyYours Environ IIJelectric floor warming system mats (“the Product”) to be free from defects in materials and workmanship for five
years from the date of manufacture, provided that the Product is installed in accordance with the WarmlyYours product installation guide, any special written or oral design
or installation guidelines provided by WarmlyYours for the specific project that the Product is intended, the provisions of the National Electric Code (NEC), and all applicable
local building and electrical codes. If the Product is determined to be defective in materials and workmanship, and has not been damaged as a result of misuse, misapplication or improper installation, WarmlyYours will reimburse the cost for location of the fault, repair of Product, and any labor and materials required to perform the repair. If repair of the Product is not feasible, WarmlyYours will replace the Product or refund the original cost of the Product. Controls sold under the WarmlyYours name are warranted for one year from date of purchase. Should the control be defective or malfunction, return the control to WarmlyYours and it will be repaired or replaced (at Warmlyyours’ option). The warranty does not cover removal or reinstallation costs. See entire warranty in packaging. Other controls carry their manufacturer’s warranty.

WarmlyYours Inc. assumes no responsibility under this warranty for any damage to the Product prior to or during installation by anyone, including, but not limited to trades
people or visitors to the job site, or damage caused as a result of post installation work. Call our toll free number, (800) 875-5285, if you have any questions about installation.
The Limited Warranty is null and void if the Product owner or his representative attempts to repair the Product without receiving authorization. Upon notification of an actual
or possible problem, WarmlyYours will issue an Authorization to Proceed under the terms of the Limited Warranty.

Warranty Subject to the Following Conditions:
1. The warranty of the warming system must be registered by completing and returning the attached ‘System Warranty Registration’ card to WarmlyYours, Inc. within thirty days of date of purchase. Please keep your invoice, as proof of date of purchase will be required in the event of a claim.
2. The warming mat must be installed flat under carpet or floating laminate wood and above a foam underlayment (also known as a pad or carpet cushion).
3. The warming
system must be electrically grounded and protected by a GFI (Ground Fault Interrupter).
4. The installation must comply with all national and local electrical and building codes, as well as any other applicable statutory requirements. 5. The manufacturer hereby reserves the right to inspect the installation site at any reasonable time.
6. The warranty is not automatically transferred with change of ownership, but the manufacturer may, on application, transfer the warranty for the period remaining. This transfer is
solely at the discretion of the manufacturer.
7. The warming system should be used strictly in accordance with the following:
7.1 Hard wire the warming system mats to a dedicated circuit. The voltage of the circuit should match the voltage of the warming system, and the size of the circuit should be such that the warming system does not occupy more than 80% of the circuit capacity.
7.2 Should you feel no warmth on the floor within 60 minutes, verify that there is power to the control or thermostat. Contact WarmlyYours after verifying that there is power at the plug point. Under no circumstances should you or anyone else tamper with or attempt to repair the warming system – this will render the warranty null and void.
7.3 Switch the warming system on and off as you would any conventional electric heater, although timers or thermostats may be used if preferred.
7.4 Use reasonable care in the operation of the warming system. Do not drop heavy articles on the flooring or pierce the flooring with sharp objects.
7.5 For under carpet applications, a pad of at least 6 pounds per cubic foot must be used.
7.6 All restrictions and warnings detailed in the installation guide must be strictly followed.

WARMLYYOURS, INC. DISCLAIMS ANY WARRANTY NOT PROVIDED HEREIN, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. WARMLYYOURS FURTHER DISCLAIMS ANY RESPONSIBILITY FOR SPECIAL, INDIRECT, SECONDARY, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT, INCLUDING INCONVENIENCE OR LOSS OF USE.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE FACE OF THIS DOCUMENT. NO AGENT OR REPRESENTATIVE OF WARMLYYOURS HAS ANY AUTHORITY TO EXTEND OR MODIFY THIS WARRANTY UNLESS SUCH EXTENSION OR MODIFICATION IS MADE IN WRITING BY A CORPORATE OFFICER.

Warranty Info Taken From:

warmlyyours.com

ThermoFlex™
RADIANT FLOOR HEATING MAT 10-YEAR LIMITED WARRANTY
Thermosoft International Corporation (“Manufacturer”) warrants that its ThermoFlex™ radiant floor heating mat(“Product”) for floating laminate flooring, floating wood flooring ceramic flooring and porcelain flooring (“Applicable Flooring”) is free from defects in manufacturing, materials and workmanship in manufacture and to perform under normal use for a period of 10 years from the date the Product was originally purchased (“Limited Warranty Period”). This warranty shall not be valid under the following conditions: 1) The preparation, conditions and installation of the Product is not in accordance with industry standards as outlined by the National Wood Flooring Association for wood floor applications, and the Tile Council of America for ceramic, porcelain and natural stone applications, The National Electric Code (NEC), the Canadian Electric Code (CEC) and all applicable local electrical and building codes; 2) the installation is not conducted as per Manufacturer’s written instructions; 3) the sub-floor is not within tolerances of vapor emissions per industry standards; 4) defective hardwood planks, tile, grout, or adhesive is used in the installation;
5) subfloor cracking, settling or displacement occurs; 6) there exists a failure of floor patching or leveling materials, or use of non-approved patching or leveling materials; or 7) improper installation materials or methods are used, 8) local overheating is caused by use not in accordance with Manufacturer’s instructions, 9) the Product is not connected to the power source by a licensed electrician, 10) the owner fails to retain and supply resistance measurements recorded during
installatio n as specified by the Manufacturer’s instructions 11) the Product’s heating elements are cut, punctured or tampered with. This limited warranty is extended to the original property developer and/or the original occupant of the property where the Product is installed (the “Owner”) and does not cover damage to the Applicable Flooring. This Limited Warranty is further subject to the exclusions and limitations provided below and on the reverse side.

TO OBTAIN WARRANTY SERVICE, FOLLOW THE INSTRUCTIONS IN STEP
4 BELOW. UPON RECEIPT OF THE DEFECTIVE PRODUCT, P APERWORK, RECEIPT AND RESISTANCE MEASURES, MANUFACTURER WILL EXAMINE AND TEST THE PRODUCT. IF IT IS DETERMINED THAT THE PRODUCT WAS PROPERLY INSTALLED AND FAILED DURING NORMAL USE AS A RESULT OF A MANUFACTURING, DEFECT, THE MANUFACTURER WILL REMEDY THE DEFECT OR FAILURE WITHOUT CHARGE TO THE CONSUMER PROVIDED MANUFACTURER RECEIVES NOTICE OF THE WARRANTY CLAIM IN THE MANNER PROVIDED BELOW WITHIN THE LIMITED WARRANTY PERIOD. THE REMEDY FOR ANY SUCH DEFECT IS LIMITED, AT MANUFACTURER’S OPTION, TO THE REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE OF THE PRODUCT. THE WARRANTY PERIOD FOR THE REPLACEMENT PRODUCT
WILL EXPIRE 10 YEARS FROM THE DATE THAT THE ORIGINAL PRODUCT WAS
PURCHASED. THIS LIMITED WARRANTY DOES NOT APPLY TO THE THERMOSTATIC CONTROL UNIT WHICH IS A SEPARATELY PURCHASED COMPONENT THAT CARRIES ITS OWN WARRANTY. MANUFACTURER WARRANT
S THAT THE PRODUCT PRODUCES THE RATED WATT OUTPUT LISTED ON THE
LABEL WHEN OPERATED AT THE RATED VOLTAGE. MANUFACTURER MAKES NO REPRESENTATION CONCERNING THE TEMPERATURE LEVEL THAT WILL BE PRODUCED BY THE PRODUCT. MANUFACTURER ASSUMES NO LIABILITY FOR THE COST OF FLOOR COVERING MATERIALS OR THE COST TO REMOVE OR
REPLACE THEM. IMPORTANT: FOR THIS WARRANTY TO BE VALID, THIS PRODUCT MUST BE CONNECTED TO A THERMOSTATIC CONTROL DEVICE WITH GROUND FAULT CIRCUIT INTERRPUPTER (GFCI) BY A LICENSED
ELECTRICIAN. THIS LIMITED WARRANTY IS FURTHER SUBJECT TO THE CONDITIONS, LIMITATIONS, AND EXCLUSIONS PROVIDED ON THE REVERSE.

CONDITIONS/EXCLUSIONS TO THE LIMITED WARRANTY
THIS 10-YEAR LIMITED WARRANTY IS FURTHER MADE SUBJECT TO THE FOLLOWING CONDITIONS AND EXCLUSIONS, PLEASE READ THE FOLLOWING CAREFULLY:
1. Required Installation. To be covered by this Limited Warranty, the Product must be installed indoors following the Manufacturer’s recommended installation instructions for the Product and the manufacturer’s recommended installation instructions for the Applicable Flooring. This Product may
only be used in “Type II” flooring applications, and is not suitable for areas exposed to constant moisture such as shower stalls, dairies, etc. This Product may not be used directly over expansion joints.
2. Limitation on Causes of Defects Covered Under Warranty. This limited warranty covers only defects in manufacturing materials or workmanship and does not cover defects, malfunctions or failures resulting from any other cause including, without limitation: (i) improper or inadequate installation; (ii) damage caused by trades people or visitors to the job site or by cutting or puncturing
or other post installation damage to the heating elements; (iii) defects caused by fire, flood, tornado, hurricane, earthquake, acts of God, differential settlement, insect infestation, extraordinary environmental conditions, riot or other civil insurrections, or acts of war or conflict; (iii) defects caused by abusive conditions or accidents, such as but not limited to cutting, severe impact or abnormal
vibrations; (iv) installation or use of the Product in any manner not recommended by the Manufacturer; and, (v) defects caused by improper or inadequate maintenance, cleaning, use or care of any Applicable Flooring installed over the Product, including without limitation, the use of improper or
unrecomm ended cleaning solutions or cleaning practices.
3. Controlling Document. This warranty is the sole and exclusive description of warranties applicable to the Product. Any written or oral representation, warranties or guarantees concerning the Product which are inconsistent with or beyond the scope of the description contained herein are superceded by
this document and deemed inapplicable or void.
4. Required Procedures to Submit a Warranty Claim. In order to obtain performance of any warranty obligation, the Owner must do the following:
Contact the Manufacturer at the toll free number listed below or by mail at the address listed below, and request a claim form or visit thermosoft.com/rma/ to download the form. Complete and return the claim form along with the defective Product, Product Label showing serial number, the original dated sales receipt and a copy of the resistance measures recorded during installation to the Manufacturer by certified mail return receipt requested within the Limited Warranty Period. The phone number and address to contact the Manufacturer for these purposes is as follows: Thermosoft International Corporation Attention:
THIS LIMITED WARRANTY IS GIVEN IN LIEU OF IMPLIED WARRANTIES. IMPLIED WARRANTIES OF MERCHANTABILILITY AND FITNESS FOR PARTICULAR PURPOSE ARE DISCLAIMED. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE. TO THE EXTENT ALLOWED BY APPLICABLE LAWS, MANUFACTURER HEREBY DISCLAIMS ANY AND ALL SUCH RIGHTS. UNDER NO CIRCUMSTANCES SHALL MANUFACTURER BE LIABLE TO THE OWNER, OR ANY OTHER PERSON FOR ANY CONSEQUENTIAL, INCIDENTAL, ECONOMIC, DIRECT, INDIRECT, GENERAL, OR SPECIAL DAMAGES ARISING OUT OF ANY BREACH OF WARRANTY, EXPRESS OR IMPLIED, UNDER THIS CONTRACT. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY HEREBY SUPERSEDES ALL PRE-EXISTING WARRANTIES, EITHER EXPRESS OR IMPLIED, RELATING TO THE PRODUCT

Warranty Info Taken From:

thermosoft.com

SunTouch heating elements are covered by a limited twenty-five (25-year ) product replacement warranty. SunTouch will carry a one- to three-year limited based on the SunStat model purchased. The SunTouch warranty is transferable to a new homeowner, unlike those from most other radiant heating companies. SunTouch warranties apply to the product, not just the original homeowner.

Warranty Info Taken From:

suntouch.com

Warranty Information
Energy Efficient Electric Radiant Floor Heating 5 Year Warranty

Products are manufactured exclusively for Speedheat® by Klimax Mfg. Ltd.

The manufacturer, Klimax Manufacturing Ltd, guarantees heating systems against failure from any manufacturing defects as well as normal wear and tear for a period of 5 years from date of installation. If the installation date cannot be determined, the invoice date to the customer or manufacturing date will be considered to be the installation date. There are no other express or implied warranties.

Liability is limited to the repair or replacement of the heating panel only, and does not extend to thermostats or any other accessories. No liability for consequential damages will be accepted.

The warranty is subject to the following conditions:

• That the customer retains proof of payment and returns a fully completed warranty registration form for each heating panel purchased to the address shown on the reverse side of the warranty registration form.
• That the installation has been carried out in accordance with the installation instructions. Any work carried out by a qualified electrician must be supported by written evidence of such work.
• That the heating panel is used in accordance with the operating instructions and precautions.

Warranty Info Taken From:

speedheat.us

LIMITED PRODUCT WARRANTY

Pentair Thermal Management warrants all goods listed below against faulty workmanship and use of defective materials when such goods are properly installed, operated, and maintained according to product documentation. All documentation regarding proper use and installation can be found on our web site at www.pentairthermal.com.
Brand Type
Raychem Heating cables, connection kits and accessories
Raychem Thermostats, controllers, panels, contactors, sensors and accessories

This warranty remains in force for a period of two (2) years from date of purchase. This warranty is only valid for products purchased and installed within the United States, Canada, Central American, or South American countries. This warranty can be amended only by a written instrument signed by a duly authorized officer of Pentair Thermal Management. This warranty expressly excludes Pentair Thermal Management’s PetroTrace and TracLoc product lines.

• What Will We Do to Correct Problems?
Pentair Thermal Management will examine and confirm that any alleged product issue covered by this Limited Warranty actually exists and occurred in the course of proper and normal use and was not caused by accident, misuse, neglect, alteration or improper installation, operation, maintenance, repair, or testing, or such other cause outside of the responsibility of Pentair Thermal Management under this Limited Warranty. Pentair Thermal Management will repair such goods or supply replacement goods or credit Buyer’s account for goods covered by this Limited Product Warranty, whichever Pentair Thermal Management may elect at its sole discretion.

• How Do You Get Service?
The Buyer should promptly notify Pentair Thermal Management, or their Pentair Thermal Management Representative, either by written correspondence or by e-mail within thirty (30) days after discovery of an alleged warranty issue. Detailed warranty claim information will be requested at this time and must be supplied by the Buyer. The Buyer may then be asked to return the goods, postage paid, to the location given by Pentair Thermal Management.

Pentair, Tracetek and Pyrotenax are owned by Pentair or its global affiliates. All other trademarks are the property of their respective owners.
Pentair reserves the right to change specifications without prior notice.
© 2013-2015 Pentair.
• What Does This Product Warranty Not Cover?
Goods subjected to misuse, neglect, alteration or improper installation, operation, maintenance, repair, or testing (or such other act or omission, not attributable to Pentair Thermal Management) are not covered by this Limited Product Warranty. Pentair Thermal Management shall in no event be liable for the cost of removal or installation, for loss or damage to or loss
of use of facilities or other property, loss of revenue, loss of use of revenue, loss of anticipated profits, or other damages or costs of any kind whatsoever, whether direct, indirect, incidental, or consequential, and in no event shall Pentair Thermal Management’s liability exceed an amount equal to the sales price.

• What Must You Do to Keep the Warranty in Effect?
Properly install, operate and maintain your Pentair Thermal Management system as specified in the associated Pentair Thermal Management installation literature.

• How Does State/Provincial Law Relate To This Warranty?
THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER REPRESENTATIONS, WARRANTIES, OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT, AND OF ANY OTHER OBLIGATION OR LIABILITY ON THE PART OF PENTAIR THERMAL MANAGEMENT, WHETHER BY STATUTE, CONTRACT, STRICT LIABILITY, TORT OR OTHERWISE.
If the goods are a consumer product in Buyer’s jurisdiction, Buyer may have additional legal rights under the applicable national/state/provincial legislation governing the sale of consumer goods. As a result, the above exclusions and/or limitations on the warranty may or may not apply.

Warranty Info Taken From:

pentairthermal.com

25 YEAR Product Warranty

Covers all Nuheat heating systems: heating mat, mesh, cable and cable combined with membrane.

All thermostats are subject to 3 years product warranty.

Simple steps to make sure you benefit from our 25 year product warranty:

Keep a copy of the tests report, relevant invoice, installation photographs and sketches
Complete online warranty registration form within 30 days from the date of installation.

25 YEAR Total Care Warranty

Total Care Warranty is everything included in the 25 year product warranty going beyond product value. Offered exclusively at no additional cost for all installations completed by Nuheat Certified PRO installers.

Certified PRO installers have followed our extensive product training, guaranteeing a flawless installation for years of comfort.

Total Care Warranty exceeds the initial 25 Years product value and covers:

Floor heating system replacement
Floor covering renovations to initial state

Warranty Info Taken From:

nuheat.com

www.easyheat.com
EasyHeat warrants that if there are any defects in material or workmanship in any heating cable or accessory (“GOODS”) during the first year after the date of purchase, unless otherwise specified by EasyHeat in writing, we will provide new products to replace any defective items, or we will refund the purchase price paid for the accessory or cable, not including any labor or other installation costs. As an alternate, we may elect to repair the cable or accessory at our factory with all shipping and other removal costs borne by the purchaser.

Our obligation to provide new products, refund the purchase price, or perform the repair described above is conditioned upon (a) the installation of the accessory or cable conforming to the directions set forth in our installation instructions and (b) the accessory or cable not having been damaged by mechanical or electrical activities unrelated to the operation of the accessory or cable. A refund of your purchase price, provision of replacement products or repair of the accessory or cable as described above, shall be your sole and exclusive remedy for a breach of
this warranty.

THESE ARE THE SOLE AND EXCLUSIVE WARRANTIES GIVEN BY EASYHEAT WITH RESPECT TO THE GOODS AND ARE IN LIEU OF AND EXCLUDE ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, ARISING BY OPERATION OF LAW OR OTHERWISE, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHETHER OR NOT THE PURPOSE OR USE HAS BEEN DISCLOSED TO EASYHEAT IN SPECIFICATIONS, DRAWINGS OR
OTHERWISE, AND WHETHER OR NOT EASYHEAT’S PRODUCTS ARE SPECIFICALLY DESIGNED AND/OR MANUFACTURED BY EASYHEAT FOR YOUR USE OR PURPOSE.

This warranty does not extend to any losses or damages due to misuse, accident, abuse, neglect, normal wear and tear, negligence, unauthorized modification or alteration, use beyond rate capacity, or improper installation, maintenance or application. To the extent that you or your agents have supplied specifications, information, representation of operating conditions or other data to EasyHeat in the selection or design of the Goods and the preparation of EasyHeat’s quotation, and in the event that actual operating conditions or other conditions differ from those represented by you, any warranties or other provisions contained herein which are affected by such conditions shall be null and void. If within thirty (30) days after your discovery of any warranty defects within the warranty period, you notify EasyHeat thereof in writing, EasyHeat shall, at its option, repair or replace F.O.B. point of manufacture, or refund the purchase price for, that portion of the Goods found by EasyHeat to be defective. Failure by you to give such written notice within the applicable time period shall be deemed an absolute and unconditional waiver of your claim for such defects. Goods repaired or replaced during the warranty period shall be covered by the foregoing warranty for the remainder of the original warranty period or ninety (90) days from the date of shipment of the repaired or replaced goods, whichever is longer.
This limited warranty does not cover any costs relating to the repair or replacement of any accessory or cable at the installation site. Our accessories and cables are not easily accessible. A failed accessory or cable usually cannot be easily repaired. Replacement of a failed accessory or cable will require that the materials under which it is installed be removed to permit replacement of the accessory or cable. We will not reimburse any costs relating to the repair or replacement of any accessory or cable at the installation site.
IN NO EVENT, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION (WHETHER BASED IN CONTRACT, INFRINGEMENT, NEGLIGENCE, STRICT LIABILITY, OTHER TORT OR OTHERWISE), SHALL EASYHEAT’S LIABILITY TO YOU AND/OR YOUR CUSTOMERS EXCEED THE PRICE PAID BY YOU FOR THE SPECIFIC GOODS PROVIDED BY EASYHEAT GIVING RISE TO THE CLAIM OR CAUSE OF ACTION. YOU AGREE THAT WE SHALL NOT BE LIABLE TO YOU
OR YOUR CUSTOMERS FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL OR PUNITIVE DAMAGES.

No agent, employee or representative of ours has authority to bind us to any affirmation, representation or warranty concerning the goods sold unless such affirmation, representation or warranty is specifically incorporated by written agreement.To obtain new products, arrange repair of existing product, or a refund under this warranty, please contact EasyHeat with a
description of the defect and proof of purchase at the address noted herein.

Warranty Info Taken From:

emersonindustrial.com

Delta-Therm MI Cable Warranty: (Snow Melting)

Limited Warranty
Delta-Therm Corporation
Agrees to repair or replace at the manufacturer’s option any Delta-Therm factory-assembled mineral insulated (MI) cable assembly which fails to function
within one year from the original invoice date if the failure is caused by defective workmanship or material or both.
Or, agrees to repair or replace at the manufacturer’s option any Delta-Therm factory-assembled MI cable assembly within ten years of the completed
installation date if all of the following conditions have been met:
1. Testing of the MI cable assembly is performed according to the installation instructions relating to the specific application;
2. Test Results and the Required Information requested on the attached sheet are sent in writing by registered mail to Delta-Therm within 30
days of the completed MI cable assembly installation;
3. The MI cable assembly is returned to Delta-Therm with proof of purchase and with a written explanation of the alleged defect(s); and/or is
available for inspection by a Delta-Therm representative within 30 days of the discovery of the defect(s). No cables may be returned without prior
authorization from Delta-Therm. For any MI cable assembly return, the consumer must prepay the shipment.
The consumer is responsible for all costs involved in removing the MI cable assembly, as well as all costs involved in reinstalling any repaired or replaced MI
cable assembly. Delta-Therm Corporation is not liable for any incidental and/or consequential and/or business interruption losses or damages. Any of the following will void this warranty: · Failure to follow Delta-Therm assembly, installation, and testing instructions, cautions, and warnings;
· Damage caused by abuse, misuse, alteration, or mechanical abrasion;
· Damage caused by inadequate maintenance or unsafe repairs or both;
· Failure to use qualified electricians for installation;
· Failure to install cable assembly according to all applicable local electrical codes and to the National Electrical Code.
Delta-Therm reserves the right to inspect the installation site(s) to determine whether this limited warranty applies.
This limited warranty is exclusive. There are no warranties of merchant ability, and There are no warranties which extend beyond The description on The face hereof.

Warranty Info Taken From:

http://www.delta-therm.com/snow-melting.html

---

Delta-Therm Self-Regulating Cable Warranty: (Roof Deicing-CO Series)

Delta-Therm Corporation
Agrees to repair or replace at the manufacturer’s option any Delta-Therm Commercial Series Self Regulating CO Series roof deicing cable which fails
to function within one year from the original invoice date if the failure is caused by defective workmanship or material or both.
The consumer is responsible for all costs involved in removing the Commercial Series Self Regulating roof deicing cable as well as all costs involved in
reinstalling any repaired or replaced Commercial Series Self Regulating roof deicing cable. Delta-Therm Corporation is not liable for any incidental and/or
consequential and/or business interruption losses or damages.
Any of the following will void this warranty:
· Failure to use appropriate Delta-Therm connection kits;
· Failure to follow Delta-Therm installation and testing instructions, cautions and warnings;
· Damage cause by abuse, misuse, alteration or mechanical abrasion;
· Damage caused by inadequate maintenance or unsafe repairs or both;
· Failure to use qualified electricians for installation;
· Failure to install cable assembly according to all applicable local electrical codes and to the National Electric Code.
· Failure to ground the systems or failure to use ground fault circuit interrupters.
Delta-Therm reserves the right to inspect the installation site(s) to determine whether this limited warranty applies.

THIS LIMITED WARRANTY IS EXCLUSIVE. THERE ARE NO WARRANTIES OF MERCHANTABILITY, AND THERE ARE NO
WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.

Delta-Therm Self-Regulating Cable Warranty: (Roof Deicing-IN Series)

Delta-Therm Corporation
Agrees to repair or replace at the manufacturer’s option any Delta-Therm Self Regulating IN Series roof and gutter cable which fails to function within
one year from the original invoice date if the failure is caused by defective workmanship or material or both.
Or, agrees to repair or replace at the manufacturer’s option any Delta-Therm Self Regulating roof and gutter cable which fails to function within
five years of the completed installation date if all of the following conditions have been met:
1. Testing of the Self Regulating roof and gutter cable is performed according to the installation instructions relating to the specific application;
2. Test results and the required information requested on the attached sheet are sent in writing to Delta-Therm (by registered mail) within 30 days of
the completed Self Regulating roof and gutter cable installation;
3. The Self Regulating roof and gutter cable is returned to Delta-Therm with proof of purchase and with a written explanation of the alleged
defect(s) and/or is available for inspection by a Delta-Therm representative within 30 days of the discovery of the defect(s). No cables may be
returned without prior authorization from Delta-Therm. For any Self Regulating roof and gutter cable the consumer must prepay the shipment.
The consumer is responsible for all costs involved in removing the Self Regulating roof and gutter cable as well as all costs involved in reinstalling any
repaired or replaced Self Regulating roof and gutter cable. Delta-Therm Corporation is not liable for any incidental and/or consequential and/or business
interruption losses or damages.
Any of the following will void this warranty:
· Failure to use appropriate Delta-Therm connection kits;
· Failure to follow Delta-Therm installation and testing instructions, cautions and warnings;
· Damage cause by abuse, misuse, alternation or mechanical abrasion;
· Damage caused by inadequate maintenance or unsafe repairs or both;
· Failure to use qualified electricians for installation;
· Failure to install cable assembly according to all applicable local electrical codes and to the National Electric Code.
· Failure to ground the systems or failure to use ground fault circuit interrupters.
Delta-Therm reserves the right to inspect the installation site(s) to determine whether this limited warranty applies.

This limited warranty is exclusive. There are no warranties of merchantability , and there are no warranties which extend
beyond the description on the face hereof.

Delta-Therm Self-Regulating Cable Warranty: (Roof Deicing-IN Series)

Delta-Therm Corporation
Agrees to repair or replace at the manufacturer’s option any Delta-Therm factory-assembled mineral insulated (MI) cable assembly which fails to function
within one year from the original invoice date if the failure is caused by defective workmanship or material or both.
Or, agrees to repair or replace at the manufacturer’s option any Delta-Therm factory-assembled MI cable assembly within ten years of the completed
installation date if all of the following conditions have been met:
1. Testing of the MI cable assembly is performed according to the installation instructions relating to the specific application;
2. Test Results and the Required Information requested on the attached sheet are sent in writing by registered mail to Delta-Therm within 30
days of the completed MI cable assembly installation;
3. The MI cable assembly is returned to Delta-Therm with proof of purchase and with a written explanation of the alleged defect(s); and/or is
available for inspection by a Delta-Therm representative within 30 days of the discovery of the defect(s). No cables may be returned without prior
authorization from Delta-Therm. For any MI cable assembly return, the consumer must prepay the shipment.
The consumer is responsible for all costs involved in removing the MI cable assembly, as well as all costs involved in reinstalling any repaired or replaced MI
cable assembly. Delta-Therm Corporation is not liable for any incidental and/or consequential and/or business interruption losses or damages.
Any of the following will void this warranty:
· Failure to follow Delta-Therm assembly, installation, and testing instructions, cautions, and warnings;
· Damage caused by abuse, misuse, alteration, or mechanical abrasion;
· Damage caused by inadequate maintenance or unsafe repairs or both;
· Failure to use qualified electricians for installation;
· Failure to install cable assembly according to all applicable local electrical codes and to the National Electrical Code.
Delta-Therm reserves the right to inspect the installation site(s) to determine whether this limited warranty applies.
This limited warranty is exclusive. There are no warranties of merchantabiliTy, and There are no warranties which extend beyond The description on The face hereof.

Warranty Info Taken From:

http://www.delta-therm.com/roof-deicing.html

---

Delta-Therm Floor Warming Cable Warranty: (FW Cable)

Delta-Therm Corporation
Agrees to repair or replace at the manufacturer’s option any Delta-Therm factory assembled silicone jacketed (FW) floor heating cable assembly which fails to function within
ONE YEAR from the original invoice date if the failure is caused by defective workmanship or material or both; or Agrees to repair or replace at the manufacturer’s option
any Delta-Therm factory assembled silicone jacketed floor heating cable assembly which fails to function within FIVE YEARS of the completed installation date if all of the following conditions have been met:
1. Testing of the floor heating cable assembly is performed according to the installation instructions relating to the specific application;
2. Test results and the required information requested on the attached sheet are sent in writing to Delta-Therm (by registered mail) within 30 days of
the completed floor heating cable assembly installation;
3. The floor heating cable assembly is returned to Delta-Therm with proof of purchase and with a written explanation of the alleged defect(s) and/or
is available for inspection by a Delta-Therm representative within 30 days of the discovery of the defect(s). No cables may be returned without
prior authorization from Delta-Therm. For any floor heating cable assembly the consumer must prepay the shipment.

The consumer is responsible for all costs involved in removing the floor heating cable assembly as well as all costs involved in reinstalling any repaired or
replaced floor heating cable assembly. Delta-Therm Corporation is not liable for any incidental and/or consequential and/or business interruption losses
or damages.

Any of the following will void this warranty:
· Failure to follow Delta-Therm installation and testing instructions, cautions and warnings;
· Damage cause by abuse, misuse, alteration or mechanical abrasion;
· Damage caused by inadequate maintenance or unsafe repairs or both;
· Failure to use qualified electricians for installation;
· Failure to install cable assembly according to all applicable local electrical codes and to the National Electric Code.
Delta-Therm reserves the right to inspect the installation site(s) to determine whether this limited warranty applies.

THIS LIMITED WARRANTY IS EXCLUSIVE. THERE ARE NO WARRANTIES OF MERCHANTABILITY, AND THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.

Delta-Therm Floor Warming Cable Warranty: (MI Cable)

Delta-Therm Corporation
Agrees to repair or replace at the manufacturer’s option any Delta-Therm factory-assembled mineral insulated (MI) cable assembly which fails to function
within one year from the original invoice date if the failure is caused by defective workmanship or material or both. Or, agrees to repair or replace at the manufacturer’s option any Delta-Therm factory-assembled MI cable assembly within ten years of the completed installation date if all of the following conditions have been met:
1. Testing of the MI cable assembly is performed according to the installation instructions relating to the specific application;
2. Test Results and the Required Information requested on the attached sheet are sent in writing by registered mail to Delta-Therm within 30 days of the completed MI cable assembly installation;
3. The MI cable assembly is returned to Delta-Therm with proof of purchase and with a written explanation of the alleged defect(s); and/or is
available for inspection by a Delta-Therm representative within 30 days of the discovery of the defect(s). No cables may be returned without prior authorization from Delta-Therm. For any MI cable assembly return, the consumer must prepay the shipment. The consumer is responsible for all costs involved in removing the MI cable assembly, as well as all costs involved in reinstalling any repaired or replaced MI cable assembly. Delta-Therm Corporation is not liable for any incidental and/or consequential and/or business interruption losses or damages.
Any of the following will void this warranty:
· Failure to follow Delta-Therm assembly, installation, and testing instructions, cautions, and warnings;
· Damage caused by abuse, misuse, alteration, or mechanical abrasion;
· Damage caused by inadequate maintenance or unsafe repairs or both;
· Failure to use qualified electricians for installation;
· Failure to install cable assembly according to all applicable local electrical codes and to the National Electrical Code.

Delta-Therm reserves the right to inspect the installation site(s) to determine whether this limited warranty applies.

This limited warranty is exclusive. There are no warranties of merchantabiliTy, and There are no warranties which ex Tend beyond The description on The face hereof.

Warranty Info Taken From:

http://www.delta-therm.com/floor-warming.html